Gebildet 19mm 15A/220VAC LED Blue Latching Push Button Switch User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Gebildet 19mm 15A/220VAC LED Blue Latching Push Button Switch. This all-metal switch is designed for various applications requiring a manual reset, boat reset, instrumentation, entry protection, or household appliance control. It features a solid, crisp push feedback and a comfortable blue LED light. Its IP65 waterproof rating allows for use in humid environments, and the metal shell tolerates vibrations and other harsh environmental conditions.

2. Consignes de sécurité

• Coupez toujours l'alimentation électrique avant toute installation ou opération de maintenance afin d'éviter les chocs électriques.
• Assurez-vous que tous les branchements électriques sont bien fixés et correctement isolés.
• Vérifiez que le voltagLes valeurs nominales de courant et de tension du commutateur correspondent aux exigences de votre application.
• L'installation doit être effectuée par une personne qualifiée si vous avez des doutes concernant le câblage électrique.
• Do not exceed the specified electrical ratings (15A, 220VAC).

3. caractéristiques du produit

• Matériel: Stainless steel shell for durability and corrosion resistance.
• Type d'opération : Latching (Push ON, Push OFF).
• Indicateur LED : Blue LED, 220VAC.
• Indice d'étanchéité : IP65, suitable for wet or dusty environments.
• Conception compacte : Short type with a total height of 2.5 cm, ideal for limited space installations.
• Structure de contact: SPST (Single Pole Single Throw), 1NO (Normally Open).
• Puissance nominale élevée : 15A/220VAC.

Figure 1: Compact design for limited space installation.

Figure 2: IP65 waterproof rating ensures protection against water and dust.

4. Configuration et installation

4.1 Contenu du paquet

• 1 x Gebildet 19mm Latching Push Button Switch
• 1 x Wiring Diagram (often included with the switch)

4.2 Montage

1. Assurez-vous que la surface de montage est propre et plane.
2. Drill a mounting hole with a diameter of 19mm (0.74 inches).
3. Insert the switch into the drilled hole.
4. Secure the switch with the provided nut. The recommended nut torque is 5-14 Nm.
5. The switch is suitable for panel thickness between 1-9 mm.

Figure 3: Detailed dimensions and specifications for mounting.

4.3 Instructions de câblage

The switch features 4 pins for connection. A simplified wiring diagram is provided to assist with installation. Ensure correct polarity for the LED if applicable, though the provided diagram typically shows AC connections.

• Type de câblage : Solder pin.
• bornes: Typically two for the switch contacts (NO) and two for the LED.

Figure 4: Wiring diagram showing two common connection methods.

Top Diagram: Device ON, Light ON; Device OFF, Light OFF. This configuration illuminates the LED only when the switch is activated and the device is powered.

Bottom Diagram: Light Always ON. This configuration keeps the LED illuminated constantly, regardless of the switch's ON/OFF state, as long as power is supplied to the LED circuit.

5. Mode d'emploi

This is a latching push button switch. Its operation is straightforward:

• Pour allumer: Press the button once. The button will remain in the depressed position, and the connected device will activate. The blue LED will illuminate (if wired for simultaneous operation).
• Éteindre: Press the button again. The button will return to its original position, and the connected device will deactivate. The blue LED will turn off (if wired for simultaneous operation).

Figure 5: Visual representation of the switch in ON and OFF states.

6. Entretien

The Gebildet push button switch is designed for durability and requires minimal maintenance.

• Nettoyage: Utilisez un chiffon doux et sec.amp cloth to clean the exterior of the switch. Avoid abrasive cleaners or solvents.
• Inspection: Vérifiez périodiquement le serrage des connexions électriques et l'absence de signes d'usure ou de corrosion.
• Caractéristique étanche : The IP65 rating protects against dust and low-pressure water jets. While suitable for humid environments, avoid prolonged submersion or high-pressure water exposure.

7. Dépannage

• Interrupteur n'activant pas l'appareil :
  • Check all wiring connections according to the diagram (Figure 4).
  • Ensure power supply to the switch and device is active.
  • Verify the device itself is functioning correctly.
• La LED ne s'allume pas :
  • Confirm the LED wiring is correct as per the diagram (Figure 4).
  • Check if the power supply to the LED circuit is present.
  • Ensure the switch is in the ON position if the LED is wired for simultaneous operation.
• Switch Not Latching/Unlatching:
  • Assurez-vous que le bouton est fermement enfoncé.
  • Inspect for any physical obstruction or damage to the button mechanism.

8. Spécifications

9. Informations sur la garantie

Gebildet products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the official Gebildet webConsultez le site web ou contactez votre point de vente. Conservez votre reçu d'achat comme preuve d'achat pour toute réclamation au titre de la garantie.

10. Assistance

If you encounter any issues or have questions regarding your Gebildet push button switch that are not covered in this manual, please contact Gebildet customer support through their official website or the retailer from whom you purchased the product. Provide your model number (E1417) and a detailed description of the issue for faster assistance.