Manuel d'utilisation du taille-haies et arbustes sans fil WORKPRO 3.6 V

Introduction

Thank you for choosing the WORKPRO 3.6V Cordless Grass and Shrub Shear. This versatile 2-in-1 tool is designed for efficient trimming of grass edges and small shrubs. It features a lightweight design, powerful motor, and a long-lasting battery for convenient outdoor use. Please read this manual carefully before operation to ensure safe and effective use of the product.

Image: The WORKPRO 3.6V Cordless Grass and Shrub Shear, showing the main unit, the grass shear blade, the shrub shear blade, and the Type-C charging cable.

Consignes de sécurité

Respectez toujours les consignes de sécurité de base lorsque vous utilisez des outils électriques afin de réduire les risques d'incendie, d'électrocution et de blessures.

• Lire le manuel : Lisez et comprenez toutes les instructions avant d'utiliser l'outil.
• Gardez la zone dégagée : Tenez les enfants, les passants et les animaux domestiques éloignés de la zone opératoire.
• Portez un équipement de protection : Always wear safety glasses, gloves, and appropriate footwear.
• Avoid Contact with Blades: Ne jamais toucher les lames lorsque l'outil est en marche ou branché.
• Prise en main sûre : Tenez toujours l'outil fermement à deux mains pendant son utilisation.
• Double Switch Safety: The tool features a double switch mechanism to prevent accidental activation. Ensure both switches are engaged for operation.
• Chargement : Use only the provided Type-C charging cable and a compatible 5V/1A charger. Do not use the tool while charging.
• Stockage: Rangez l'outil dans un endroit sec et sûr, hors de portée des enfants.

Image: Close-up of the ergonomic safety lock and ON/OFF switch, highlighting the dual activation mechanism for safe operation.

Contenu du colis

Vérifiez que tous les articles sont présents et en bon état lors du déballage :

• 1 x WORKPRO Grass and Shrub Shear Unit
• 1 x Grass Blade (75 mm wide)
• 1 x Shrub Blade (120 mm length)
• 1 x câble de chargement de type C
• 1 x Manuel d'utilisation

Produit terminéview

Familiarize yourself with the components of your WORKPRO shear:

Image: Diagram showing key components: Type-C Charging Port with Indicator, Type-C Cable (1M), Safety Lock-off Button, ON/OFF Switch, Blade Release Button, TPR Anti-Slip Handle, and Shrub Blade. The unit weighs approximately 370g.

• Unité principale : Ergonomic body with integrated motor and battery.
• Grass Blade: Designed for trimming grass edges, 75mm cutting width.
• Shrub Blade: Designed for shaping shrubs and small branches, 120mm cutting length.
• Port de charge de type C : Pour recharger la batterie interne.
• Bouton de verrouillage de sécurité : Empêche les démarrages accidentels.
• Interrupteur marche / arrêt: Activates the motor when the safety lock is disengaged.
• Bouton de libération de la lame : Permet un changement de lame rapide et facile.
• TPR Anti-Slip Handle: Offre une prise en main confortable et sûre.

Installation

Charger la batterie

The tool is equipped with a 2000mAh Lithium-ion battery. Before first use, fully charge the battery.

1. Repérez le port de chargement de type C sur l'outil.
2. Connect the provided Type-C charging cable to the tool and to a 5V/1A USB power source (e.g., power bank, Type-C charger, car charger, laptop/PC USB port). Note: USB charging brick is not included.
3. Le voyant de charge s'allumera (généralement en rouge) pendant la charge.
4. Once fully charged, the indicator light will change (typically green). Charging time is approximately 2-3 hours.
5. Débranchez le chargeur une fois la charge terminée.

Image: Illustration of the WORKPRO shear being charged via a Type-C cable, showing compatible power sources like a power bank, Type-C charger, car charger, and laptop/PC. The charging indicator lights (red for charging, green for fully charged) are also depicted.

Installation/changement des lames

Ensure the tool is turned off and disconnected from any power source before changing blades.

1. Press the Blade Release Button located on the top of the tool.
2. Carefully remove the currently installed blade by pulling it away from the unit.
3. Align the desired blade (grass or shrub) with the slot on the tool.
4. Push the blade firmly into place until it clicks, indicating it is securely locked.
5. Verify the blade is securely attached by gently pulling on it.

Image: Diagram illustrating the dimensions of both the grass and shrub blades, and a close-up showing the easy and safe blade change mechanism with the blade release button.

Mode d'emploi

Always wear appropriate safety gear before operating the shear.

Démarrage et arrêt de l'outil

1. Ensure the desired blade is securely installed.
2. Tenez fermement l’outil.
3. To start, press and hold the Safety Lock-off Button with your thumb.
4. While holding the safety button, press the ON/OFF Switch with your index finger. The blades will begin to move.
5. To stop, release the ON/OFF Switch. The blades will stop.

Utilisation de la lame de cisaille à gazon

The grass shear blade is ideal for trimming grass edges around flowerbeds, pathways, and other areas inaccessible to larger mowers.

• Ensure the grass blade (75mm wide) is installed.
• Hold the tool with the blade parallel to the ground or at a slight angle for precise edging.
• Move the tool slowly and steadily along the grass edge.
• Avoid cutting wet grass, as it can clog the blades and reduce efficiency.

Image: Depicts the two cutting modes: Grass Shear with a maximum cutting width of 75mm, and Hedge Trimmer with a maximum cutting length of 118mm and maximum cutting thickness of 7.8mm.

Using the Shrub Shear Blade

The shrub shear blade is suitable for shaping and trimming small shrubs, hedges, and ornamental plants. It can cut branches up to 7.8mm in diameter.

• Ensure the shrub blade (120mm length) is installed.
• Hold the tool at a comfortable angle for trimming.
• Work in small sections, making smooth, even passes.
• Do not force the blades through thick branches. If resistance is met, reposition the tool or use a different cutting tool for larger branches.

Image: Collage showing the WORKPRO shear being used for various trimming tasks, including shaping small trees, weeding, and trimming potted plants, demonstrating its versatility.

Entretien

Un entretien régulier garantit des performances optimales et prolonge la durée de vie de votre outil.

Nettoyage

• Always turn off the tool and remove the blade before cleaning.
• Use a soft brush or cloth to remove debris, sap, and dirt from the blades and housing.
• Do not use abrasive cleaners or solvents, as they can damage the plastic parts.
• Essuyez les lames avec un chiffon légèrement huilé pour éviter la rouille.

Entretien de la lame

• The blades are made of premium 65Mn steel for high hardness and wear resistance.
• Inspect blades regularly for damage or dullness.
• If blades become dull, they can be sharpened by a professional or replaced.
• Store blades in a dry place to prevent corrosion.

Image : Gros plan view of the premium 65Mn steel blades, emphasizing their high hardness, wear resistance, sharpness, and long life.

Stockage

• Rangez l'outil dans un endroit frais et sec, à l'abri de la lumière directe du soleil et de l'humidité.
• Assurez-vous que la batterie est partiellement chargée (environ 50 %) avant un stockage à long terme afin de préserver sa santé.
• Tenir hors de portée des enfants et des utilisateurs non autorisés.

Dépannage

Caractéristiques

Image: Visual representation of the upgraded power motor (1100rpm) and the long-lasting 2000mAh Lithium-ion battery, indicating over 40 minutes of no-load operation time.

Garantie et assistance

Pour toute information relative à la garantie ou pour obtenir une assistance technique, veuillez contacter le fabricant ou votre point de vente. Conservez votre reçu d'achat comme preuve d'achat.

Fabricant: Hang Zhou Great Star Industrial Co.,LTD

For further assistance, visit the WORKPRO official website ou contactez leur service client.