Solaxx CLGE40

Solaxx CLGE40 Resilience E Series 40K Gal All-in-1 User Manual

Model: CLGE40

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Solaxx CLGE40 Resilience E Series 40K Gal All-in-1 system. Please read this manual thoroughly before attempting to install or operate the unit to ensure safe and efficient use.

The Solaxx CLGE40 is designed to provide efficient water treatment for pools up to 40,000 gallons, integrating multiple functions into a single, compact unit.

2. Consignes de sécurité

Always observe the following safety precautions to reduce the risk of injury, electric shock, fire, or damage to the unit.

  • Sécurité électrique : Ensure the unit is connected to a properly grounded outlet. Do not operate with damaged cords or plugs. Disconnect power before servicing.
  • Manipulation de produits chimiques : Follow all manufacturer's instructions for handling pool chemicals. Avoid direct contact with skin and eyes.
  • Installation: L'installation doit être effectuée par un professionnel qualifié, conformément à toutes les normes électriques et de plomberie locales et nationales.
  • Qualité de l'eau : Maintain proper water chemistry as specified in this manual to ensure optimal performance and longevity of the unit.
  • Enfants et animaux domestiques : Tenez les enfants et les animaux domestiques éloignés de l'appareil pendant son fonctionnement et son entretien.

3. Produit terminéview

Devant view of the Solaxx CLGE40 Resilience E Series 40K Gal All-in-1 unit, showing the control panel and main housing.

Figure 3.1 : Face avant view of the Solaxx CLGE40 Resilience E Series 40K Gal All-in-1 unit. This image displays the main body of the unit, including the control panel with various indicators and buttons, and the transparent cell housing below.

Incliné view of the Solaxx CLGE40 Resilience E Series 40K Gal All-in-1 unit, highlighting the transparent cell and connection points.

Figure 3.2 : Angulaire view of the Solaxx CLGE40 Resilience E Series 40K Gal All-in-1 unit. This perspective provides a clearer view of the transparent cell, which allows for visual inspection, and the plumbing connection points on either side.

The CLGE40 system integrates a salt chlorine generator with advanced control features. Key components include the control unit, the electrolytic cell, and various sensors for optimal performance.

4. Configuration et installation

4.1 Liste de contrôle de pré-installation

  • Vérifiez que tous les composants sont présents et non endommagés.
  • Ensure adequate space for installation and maintenance.
  • Confirm power supply meets unit requirements (refer to specifications).
  • Have necessary plumbing tools and materials ready.

4.2 Installation de plomberie

  1. Select an appropriate location in the return line after the filter and heater.
  2. Cut the existing PVC pipe and install the provided unions.
  3. Securely attach the electrolytic cell to the unions, ensuring proper flow direction as indicated on the cell.
  4. Apply PVC cement to all connections for a watertight seal. Allow adequate curing time.

4.3 Connexion électrique

  1. Assurez-vous que le courant est coupé au niveau du disjoncteur.
  2. Connect the control unit to a dedicated, grounded electrical outlet or circuit as per local electrical codes.
  3. Connect the cell cable to the control unit.
  4. Do not restore power until all connections are secure and the system is filled with water.

5. Mode d'emploi

5.1 Démarrage initial

  1. Ensure pool water chemistry is balanced (pH, alkalinity, calcium hardness).
  2. Add pool salt to achieve the recommended salinity level (typically 3000-3500 ppm). Allow salt to dissolve completely.
  3. Allumez la pompe de la piscine.
  4. Restore power to the Solaxx CLGE40 unit.
  5. Press the "ON/OFF" button to activate the unit.

5.2 Réglage du débit de chlore

The unit features an adjustable output level to control chlorine production. Use the "+" and "-" buttons on the control panel to increase or decrease the output percentage. Monitor your pool's free chlorine level and adjust as needed to maintain desired sanitation.

5.3 Voyants lumineux

  • MARCHE/ARRÊT : Indique l'état de l'alimentation.
  • SORTIE: Bar graph showing current chlorine production level.
  • FAIBLE EN SEL : Illuminates when salt level is below optimal. Add salt.
  • PAS DE FLUX: Indicates insufficient water flow through the cell. Check pump and plumbing.
  • EAU FROIDE: Illuminates if water temperature is too low for efficient operation.
  • CLEAN CELL: Indicates the cell requires cleaning.
  • CELL LIFE LOW: Indicates the electrolytic cell is nearing the end of its lifespan and may need replacement soon.

6. Entretien

6.1 Nettoyage des cellules

The electrolytic cell may accumulate scale deposits over time, reducing efficiency. The "CLEAN CELL" indicator will illuminate when cleaning is required.

  1. Turn off the unit and pool pump, and disconnect power.
  2. Remove the electrolytic cell from the plumbing.
  3. Prepare a cleaning solution of 1 part muriatic acid to 4 parts water in a plastic container. Always add acid to water, never water to acid.
  4. Submerge the cell plates in the solution, ensuring the electrical connections remain dry.
  5. Allow to soak until bubbling stops (typically 5-15 minutes). Do not over-soak.
  6. Rinse the cell thoroughly with fresh water.
  7. Reinstall the cell and restore power.

6.2 Hivérisation

In areas subject to freezing temperatures, the unit must be properly winterized to prevent damage.

  • Débranchez l’alimentation de l’appareil.
  • Drain all water from the electrolytic cell and plumbing lines connected to the unit.
  • Remove the cell and store it in a dry, temperature-controlled environment.

7. Dépannage

ProblèmeCause possibleSolution
"LOW SALT" indicator onLow salt level in pool water.Test salt level and add salt as needed. Allow time for dissolution.
"NO FLOW" indicator onInsufficient water flow through cell.Check pool pump operation, filter cleanliness, and ensure valves are open.
"CLEAN CELL" indicator onScale buildup on cell plates.Clean the electrolytic cell as per Section 6.1.
Low chlorine outputLow salt, dirty cell, low water temperature, or incorrect output setting.Check salt level, clean cell, ensure water temperature is adequate, increase output setting.
L'unité ne s'allume pasNo power supply, tripped breaker, or faulty connection.Check power outlet, reset circuit breaker, ensure all electrical connections are secure.

8. Spécifications

  • Modèle: CLGE40 Resilience E Series
  • Maximum Pool Size: 40,000 gallons
  • Fabricant: Solaxx
  • Dimensions du colis : 12 x 12 x 8 pouces
  • ASIN: B0B96WPR34
  • Recommended Salt Level: 3000-3500 ppm

Remarque: les spécifications peuvent être modifiées sans préavis.

9. Garantie et assistance

For warranty information, please refer to the warranty card included with your product or visit the official Solaxx webConsultez le site. Conservez votre preuve d'achat pour toute réclamation au titre de la garantie.

For technical support, troubleshooting assistance, or to order replacement parts, please contact Solaxx Customer Service:

When contacting support, please have your product model number (CLGE40) and serial number ready.

© 2024 Solaxx. All rights reserved.