XYZprinting Open Smart Tag Manuel d'instructions

1. Introduction

The XYZprinting Open Smart Tag is an NFC chip designed to enable compatibility with third-party filaments on select XYZprinting 3D printers. This device allows users to expand their material options beyond proprietary filaments, offering greater versatility and choice for 3D printing projects. It integrates seamlessly to provide a reliable and efficient printing experience with a wider range of materials.

Caractéristiques principales :

• Third-Party Filament Compatibility: Unlocks the ability to use filaments from various brands.
• Installation rapide : Designed for straightforward setup on your filament spool and registration with the printer.
• Spool Size Versatility: Supports a wide range of filament spool sizes, from 600g to larger capacities.
• Broad Printer Compatibility: Compatible with da Vinci nanoSeries, miniSeries, Jr. Series, and Color Series printers.
• Wide Material Support: Enables use of various filament types including PLA, PETG, ABS, and Carbon-infused materials.

2. Contenu du colis

Vérifiez que tous les éléments sont présents dans le colis :

• Open Smart Tag device (Model: RSFLAXUS00F)
• Mounting hardware (if applicable, typically a screw for attachment)

Figure 1 : Face avant view of the Open Smart Tag device. This image shows the white plastic housing with two curved arms designed to hold a filament spool, and a central rectangular section containing the NFC chip. A small screw is visible on one side.

3. Configuration et installation

Follow these steps to install and register your Open Smart Tag:

1. Attach to Filament Spool: Secure the Open Smart Tag to your third-party filament spool. The design typically allows it to clip or screw onto the spool's core. Ensure it is firmly attached and does not interfere with the spool's rotation.
2. Charger le filament : Load the filament spool with the attached Open Smart Tag into your XYZprinting 3D printer according to your printer's standard filament loading procedure.
3. Mise sous tension de l'imprimante : Turn on your 3D printer and ensure it is connected to the internet (if required for registration).
4. Access Printer Interface: Navigate to the filament management or settings section on your printer's control panel or through the associated software.
5. Register Smart Tag:
   • Locate the option to "Register Smart Tag" or "Add New Filament." This may be found by clicking on a question mark icon next to the filament status or a similar prompt.
   • The printer will attempt to read the NFC chip on the Open Smart Tag. Assurer la tag is positioned correctly for the printer's NFC reader.
   • Note: Some users have reported that with newer software versions (e.g., 2023 software), you might need to try clicking the registration prompt multiple times or ensure the printer is directly connected via USB/Ethernet for successful registration if experiencing "printer reacted too slow" errors.
6. Sélectionnez le type de filament : Once recognized, you will be prompted to select the type of filament (e.g., PLA, PETG, ABS) and potentially other parameters like diameter and color. Configure these settings to match your third-party filament.
7. Confirmation: The printer should confirm successful registration and display the new filament information.

Figure 2 : Angulaire view of the Open Smart Tag, highlighting the label with "OPEN SMART TAG" and "Model No.: RSFLA". This image provides a clearer view of the central NFC module and its identification markings.

4. Mode d'emploi

Once the Open Smart Tag is installed and registered, your XYZprinting 3D printer will treat the third-party filament as a recognized material. You can then proceed with your printing tasks as usual.

1. Préparer le modèle 3D : Use your preferred slicing software (e.g., XYZprint, Cura, Simplify3D) to prepare your 3D model for printing.
2. Select Filament Profile: In the slicing software, ensure you select the correct filament profile that matches the third-party material you are using (e.g., PLA, PETG). Adjust print settings (temperature, speed, retraction) as recommended by the filament manufacturer.
3. Démarrer l'impression : Send the sliced G-code to your printer and initiate the print job. The printer will now utilize the third-party filament as enabled by the Open Smart Tag.
4. Impression sur écran : Observe the initial layers of your print to ensure proper adhesion and extrusion. Adjust settings if necessary.

Important: Always refer to the specific recommendations of your third-party filament manufacturer for optimal printing temperatures and speeds. The Open Smart Tag facilitates the use of these materials but does not automatically configure all print settings.

5. Entretien

L'Open Smart Tag requires minimal maintenance. To ensure its longevity and proper function:

• Garder propre: Periodically wipe the device with a dry, soft cloth to remove dust or filament debris. Avoid using harsh chemicals or abrasive materials.
• Évitez les dommages physiques : Gérez intelligemment Tag carefully to prevent cracks or damage to the NFC chip.
• Stockage approprié : When not in use, store the Smart Tag in a dry, cool environment, away from direct sunlight or extreme temperatures.
• Vérifiez la connexion : Assurez-vous que tag remains securely attached to the filament spool during printing to prevent dislodgement.

6. Dépannage

If you encounter issues while using the Open Smart Tag, se référer aux problèmes et solutions courants suivants :

• Intelligent Tag Non reconnu :
  • Assurez-vous d'être intelligent Tag is correctly and securely attached to the filament spool.
  • Verify that the filament spool with the tag is properly loaded into the printer.
  • Check your printer's software/firmware version. If it's a newer version, you might need to try clicking the "Register Smart Tag" prompt multiple times.
  • Ensure your printer has a stable internet connection or is connected via USB/Ethernet during registration, as connectivity issues can sometimes cause "printer reacted too slow" errors.
  • Restart the printer and attempt the registration process again.
• Filament Not Extruding/Poor Print Quality:
  • This is often related to incorrect print settings for the specific third-party filament. Double-check the recommended nozzle temperature, bed temperature, and print speed from the filament manufacturer.
  • Ensure the filament is loaded correctly and not tangled.
  • Perform a nozzle cleaning or cold pull if you suspect a clog.
• Printer Displays "Proprietary Filament Required" Error:
  • This indicates the Smart Tag was not successfully registered or is no longer recognized. Repeat the registration steps in Section 3.
  • Assurez-vous d'être intelligent Tag itself is not damaged.

If problems persist, contact XYZprinting customer support or refer to their official support resources.

7. Spécifications

8. Garantie et assistance

For warranty information, technical support, or service inquiries, please visit the official XYZprinting webConsultez leur site web ou contactez leur service client. Conservez votre reçu d'achat comme preuve d'achat.

XYZprinting Official Website: www.xyzprinting.com