infactory Wireless Weather Station with 3 Outdoor Sensors and LCD Display

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your infactory Wireless Weather Station. This device is designed to monitor indoor and outdoor temperature and humidity, display weather trends, and record minimum and maximum values. Please read this manual thoroughly before using the product to ensure correct operation and to prevent damage.

2. Contenu du colis

Veuillez vérifier le contenu du colis lors du déballage :

• 1x infactory Wireless Weather Station (Main Unit)
• 3 capteurs extérieurs sans fil
• 1x Manuel d'utilisation (ce document)

3. Consignes de sécurité

• Tenez l'appareil à l'écart des températures extrêmes, de la lumière directe du soleil, des fortes vibrations et de l'humidité.
• Ne pas démonter ni modifier l'appareil. Les réparations doivent être effectuées uniquement par du personnel qualifié.
• Use only specified batteries (AA/Mignon). Ensure correct polarity when inserting batteries.
• Retirez les piles si l’appareil ne doit pas être utilisé pendant une période prolongée.
• Gardez les piles hors de portée des enfants.

4. Installation

4.1 Installation de la batterie

1. Unité principale : Open the battery compartment on the back of the main unit. Insert 2x AA/Mignon batteries (not included), observing the correct polarity (+/-). Close the compartment.
2. Capteurs sans fil: For each of the three wireless sensors, open the battery compartment. Insert 2x AA/Mignon batteries (not included), observing the correct polarity (+/-). Close the compartment.

4.2 Placement et appariement des capteurs

The main unit will automatically search for signals from the wireless sensors once batteries are installed. Ensure sensors are within range (up to 60 meters in open air).

• Placement de l'unité principale : The main unit features foldable feet, allowing it to be placed on any flat surface, such as a desk or shelf.
• Emplacement du capteur : The wireless sensors can be placed on a flat surface or hung using the integrated hanging eyelet. For accurate outdoor readings, place sensors in a shaded, protected area away from direct sunlight and rain. Ideal locations include a patio, balcony, or garden shed.

5. Mode d'emploi

5.1 Affichage terminéview

The LCD display (9.5 cm diagonal) simultaneously shows indoor and outdoor temperature and humidity. It also features a comfort index and weather trend icons.

5.2 Reading Data

• Lectures d'intérieur : The top section of the display shows the indoor temperature and humidity.
• Lectures en plein air : The lower section displays readings from the three wireless outdoor sensors (CH1, CH2, CH3). You can cycle through these channels or view them simultaneously, depending on the model's specific display layout.
• Tendances météorologiques : Icons on the display indicate the predicted weather trend (e.g., sunny, cloudy, rainy).
• Comfort Index: An icon or indicator shows the indoor comfort level based on temperature and humidity.

5.3 Minimum/Maximum Memory

The weather station automatically records the minimum and maximum temperature and humidity values for both indoor and outdoor readings. Consult the specific buttons on your device (e.g., 'MIN/MAX' button) to view these recorded values. These values are typically reset automatically at midnight or can be manually cleared.

6. Entretien

6.1 Nettoyage

Wipe the device and sensors with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the surfaces.

6.2 Remplacement de la batterie

When the battery indicator appears on the display, replace the batteries in the main unit or the respective sensor. Always replace all batteries in a unit at the same time with new ones of the same type.

7. Dépannage

• Lecture interdite en extérieur : Ensure batteries are correctly inserted in the sensor and the main unit. Check if the sensor is within the 60-meter range and free from major obstructions. Try re-pairing the sensor by removing and reinserting its batteries, then doing the same for the main unit.
• Lectures inexactes : Ensure sensors are not exposed to direct sunlight, strong winds, or heat sources, which can affect accuracy. Allow some time for the sensors to stabilize after placement.
• L'écran ne fonctionne pas : Vérifiez le niveau des piles et remplacez-les si nécessaire. Assurez-vous que les piles sont insérées en respectant la polarité.

8. Spécifications

9. Garantie et assistance

This product comes with a standard manufacturer's warranty. For detailed warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support or service inquiries, please contact infactory customer service.