HTU Car Phone Holder Model BS-G126 User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your HTU Car Phone Holder Model BS-G126. Please read this manual carefully before use to ensure proper functionality and safety.

2. Contenu de la boîte

Le package comprend les composants suivants :

• 1 x Adjustable Phone Holder (fits large phones/thick cases)
• 1 x HTU Cable Manager
• 1 x ventouse
• 1 x Air Vent Clip (fits vertical/horizontal air vents)
• 1 x Manuel d'utilisation
• 1 x boîte d'emballage

Figure 2.1 : Composants inclus

3. Configuration et installation

The HTU Car Phone Holder offers multiple mounting options: dashboard, windshield, and air vent.

Figure 3.1 : Plusieurs options de montage

3.1 Préparation générale

1. Ensure the mounting surface (dashboard, windshield, or air vent) is clean and dry. Use a wet cloth to wipe the dashboard if necessary.
2. For optimal adhesion, install the suction cup in a temperature range of 68°F to 77°F (10°C to 25°C) and allow 1 hour before use.

3.2 Installation du support à ventouse (tableau de bord/pare-brise)

1. Unscrew the nut on the back of the phone holder.
2. Place the nut around the ball joint of the telescopic arm.
3. Insert the ball joint into the holder socket and screw the nut tightly to secure.
4. Nettoyez soigneusement la surface de montage souhaitée.
5. Retirez le film protecteur de la ventouse.
6. Press the suction cup firmly onto the surface for 5 seconds.
7. Press the lock button on the suction cup base after 3 seconds to create a strong vacuum seal.
8. Adjust the two knobs on the telescopic arm to find the suitable viewing angle and distance.

Figure 3.2: Suction Cup Installation Steps

3.3 Air Vent Clip Installation

1. Unscrew the nut on the back of the phone holder.
2. Place the nut around the ball joint of the air vent clip.
3. Insert the ball joint into the holder socket and screw the nut tightly to secure.
4. Attach the air vent clip to a suitable air vent blade. Ensure it is securely fastened.

Figure 3.3: Air Vent Clip Installation

4. Mode d'emploi

4.1 Inserting and Removing Your Phone

1. To open the holder arms, press the release buttons located on the sides of the holder.
2. Place your phone into the holder, ensuring it rests on the bottom support feet.
3. Gently push the side arms inwards until they securely grip your phone. The holder is designed to accommodate phones from 4 to 7 inches, including those with thick cases.
4. To remove your phone, press the release buttons on the sides, and the arms will open.

Figure 4.1: Phone Compatibility and Insertion

4.2 Réglage ViewAngle d'attaque

The phone holder features a 360° rotatable ball joint and an adjustable telescopic arm (up to 9.84 inches / 24.9 cm) for optimal viewing angles. The installation angle can be adjusted up to 270 degrees.

• Rotate the phone holder to switch between portrait and landscape orientations.
• Adjust the telescopic arm length and angle using the knobs to position your phone for safe and relaxed driving.

Figure 4.2: Multi-Angle Flexible Adjustment

4.3 Gestion des câbles

Use the included HTU Cable Manager to keep your charging cable tidy and prevent tangles. Attach it to a suitable position on your dashboard or console.

Figure 4.3: Cable Manager in Use

5. Entretien

5.1 Cleaning the Suction Cup

If the suction cup loses its stickiness, rinse it with warm water and air-dry it. This will restore its adhesive properties.

Figure 5.1: Cleaning the Suction Cup

5.2 Nettoyage général

Essuyez le support de téléphone avec un chiffon doux et sec.amp Nettoyer avec un chiffon si nécessaire. Éviter d'utiliser des produits chimiques agressifs ou des nettoyants abrasifs.

6. Dépannage

6.1 Ventouse qui ne colle pas

• Ensure the dashboard or windshield surface is clean and dry before installation.
• Rinse the suction cup with warm water and air-dry to restore stickiness.
• Certain surfaces, such as leather (except faux leather/synthetic leather), waxed, or oiled dashboards, are not compatible with the suction cup. Use the mount on the windshield or air vent instead.
• For maximum adhesion, install the suction cup in a temperature range of 68°F to 77°F (10°C to 25°C) and leave it for 1 hour before use.

6.2 Phone Holder Instability

• Ensure all knobs and the suction cup lock are securely tightened after installation.
• The holder features a triangular structure and robust clamping force to maintain stability even on bumpy roads or during sudden braking.

Figure 6.1: Stable Design for Various Road Conditions

6.3 Overheating in High Temperatures

• When the temperature is above 95°F (35°C) or when your car is constantly exposed to direct sunlight, it is recommended to use the air vent clip instead of the suction cup. This can also help cool your phone.

6.4 No Wireless Charging

• This product does not include wireless charging functionality. Please use a charging cable with the provided cable manager.

7. Spécifications

Figure 7.1 : Dimensions du produit

8. Garantie et assistance

The HTU Car Phone Holder Model BS-G126 comes with a 5-year support period, including refund or replacement options. For any inquiries or assistance, please contact HTU customer service.