Système d'alarme stroboscopique d'urgence à distance SINGCALL (modèle J008 APE520C 1-2) - Manuel d'utilisation

1. Introduction

This manual provides comprehensive instructions for the setup, operation, maintenance, and troubleshooting of your SINGCALL Remote Emergency Strobe Siren Alarm System, Model J008 APE520C 1-2. This system is designed to provide a loud audible alarm and a visual strobe light in emergency situations, activated by remote call buttons.

2. Consignes de sécurité

• Ensure the siren is installed in a location where its sound and light can be effective without causing undue disturbance.
• Keep the device away from extreme temperatures and direct water exposure, unless specifically designed for outdoor use. The siren is waterproof, but ensure proper installation.
• N’essayez pas d’ouvrir ou de réparer l’appareil vous-même, car cela pourrait annuler la garantie et présenter des risques pour la sécurité.
• The siren produces a loud sound (up to 120dB). Avoid prolonged exposure to prevent hearing damage.

3. Contenu du colis

• 1 x SINGCALL J008 Strobe Siren
• 2 x SINGCALL APE520C Call Buttons
• Power Adapter for Siren
• Matériel de montage (vis, pastilles adhésives)
• Manuel d'instructions

4. Produit terminéview

4.1. J008 Strobe Siren

• Features a red indicator light that blinks with a loud beep, lasting up to 5 minutes or until canceled.
• Sound output: 120dB.
• Dimensions: 4.4 x 7.9 x 2.8 inches (11.2 x 20.1 x 7 cm).
• Weight: 0.59 lb (270g).
• Equipped with a backup battery and an anti-tampeuh interrupteur.
• Waterproof design for outdoor and indoor use.

4.2. APE520C Call Buttons

• Flexible square design with a large 2-inch diameter round call button.
• Sensitive touch reaction for convenient calling.
• 360-degree waterproof handling.
• Simple push-bottom base for easy battery changes (no screws).
• Uses 2 x 12V 23A alkaline batteries.
• Stable signal with long transmitting distance (up to 300ft).

5. Installation

5.1. Siren Installation

The J008 Strobe Siren can be mounted on a wall using the provided screws or placed on a tabletop. Ensure it is connected to a power source using the included power adapter. The siren also has a backup battery for continued operation during power outaget.

5.2. Call Button Installation

The APE520C Call Buttons can be installed using adhesive pads or screws. The back plate is removable for easy mounting. Place the call buttons in easily accessible locations where assistance might be needed, such as near a bed, in a bathroom, or at a reception desk.

5.3. Pairing Call Buttons with Siren (Registration)

To register a call button with the siren:

1. Open the back cover of the siren.
2. Connect the power adapter to the siren.
3. Appuyez sur le ENSEMBLE button on the siren's circuit board. The siren's indicator light will illuminate.
4. Appuyez sur le APPEL button on the APE520C Call Button. The siren will beep once, indicating successful pairing.
5. Repeat for any additional call buttons.
6. Close the back cover of the siren.

6. Mode d'emploi

6.1. Activation de l'alarme

To activate the emergency alarm, simply press the large APPEL button on the APE520C Call Button. The siren will emit a loud sound and the red strobe light will flash. The alarm will continue for the set duration (default 5 minutes) or until manually canceled.

6.2. Désactivation de l'alarme

To deactivate the alarm, press the small ANNULER button located on the APE520C Call Button. The siren will stop sounding and the strobe light will cease flashing.

7. Entretien

7.1. Adjusting Volume and Alarm Duration

The volume and alarm duration settings can be adjusted by accessing the internal circuit board of the siren. Refer to the video below for detailed instructions on how to open the siren and adjust the jumpers for desired settings (120dB, 100dB, 80dB, 0dB for volume; 30s, 1M, 3M, 10M for duration).

7.2. Call Button Battery Replacement

The APE520C Call Buttons are powered by 2 x 12V 23A alkaline batteries. When the indicator light on the call button no longer illuminates or the signal range decreases, it's time to replace the batteries. The design allows for simple battery changes without needing tools to remove screws from the base.

8. Dépannage

• Sirène non sonore/non clignotante : Check if the siren is properly connected to power. Ensure the backup battery is charged. Verify that the call button is paired correctly (refer to Section 5.3).
• Call button not activating siren: Check the call button batteries and replace if necessary. Ensure the call button is within the effective range (up to 300ft).
• Activation accidentelle : Ensure call buttons are placed in locations where they are not easily pressed by accident.
• Siren volume too low/high or duration incorrect: Adjust the internal settings as described in Section 7.1.

9. Spécifications

10. Garantie et assistance

For warranty information and technical support, please refer to the documentation included in your product packaging or contact SINGCALL customer service directly. Keep your purchase receipt for warranty claims.