1. Produit terminéview
The Total TWP47506 750W Automatic Jet Water Pump is designed for efficient clean water collection and distribution. It is suitable for drawing water from wells, boreholes, open tanks, and other water supply sources. Primary applications include watering vegetable gardens, personal plots, and ensuring water circulation in fountains and various water features. Its design prioritizes ease of maintenance and portability, featuring an external tank location. The pump incorporates a brushless induction motor for long-lasting, maintenance-free operation. The robust cast iron pump casing can be rotated 90 degrees for flexible installation. This pump is capable of integration into automated water supply systems.
Figure 1 : Total TWP47506 750W Automatic Jet Water Pump. This image shows the complete pump unit with its motor and casing.
2. Consignes de sécurité
Read all safety warnings and instructions carefully before operating this product. Failure to follow these instructions may result in electric shock, fire, and/or serious injury.
Sécurité générale
- Portez toujours un équipement de protection individuelle (EPI) approprié tel que des lunettes de sécurité et des gants.
- Veillez à placer la pompe sur une surface stable et plane afin d'éviter tout basculement.
- Tenir les enfants et les personnes non autorisées à l'écart de la zone d'opération.
- Ne pas utiliser la pompe dans des atmosphères explosives, telles qu'en présence de liquides, de gaz ou de poussières inflammables.
- Never use the pump to transfer flammable, corrosive, or explosive liquids.
- Disconnect the power supply before performing any maintenance, cleaning, or when the pump is not in use.
Sécurité électrique
- Assurer l'alimentation voltage matches the specifications on the pump's rating label (220-240V, 50Hz).
- Use a properly grounded outlet. Do not modify the plug.
- Do not expose the pump or electrical connections to rain or wet conditions.
- Avoid using extension cords unless absolutely necessary. If an extension cord is used, ensure it is rated for outdoor use and has the correct gauge for the pump's power requirements.
- Never carry the pump by its power cord.
- Regularly inspect the power cord for damage. If damaged, have it replaced by a qualified electrician.
3. Contenu du colis
Vérifiez que tous les éléments énumérés ci-dessous sont présents et non endommagés lors du déballage :
- 1 x Total TWP47506 750W Automatic Jet Water Pump
- 1 x pressostat
- 1 x Stainless Steel Hose
- 1 manomètre
- 1 x Three-way Brass Fitting
- Manuel de l'utilisateur (ce document)
4. Spécifications techniques
| Spécification | Valeur |
|---|---|
| Numéro de modèle | TWP47506 |
| Taper | Self-priming Automatic Jet Pump |
| Puissance nominale | 750W (1.0CV) |
| Voltage | 220-240V |
| Fréquence | 50 Hz |
| Tête max | 45 mètres |
| Débit maximal | 60 litres/minute |
| Max aspiration | 9 mètres |
| Diamètre du tuyau | 1 x 1 pouces |
| Type de moteur | Copper Wire Induction Motor (Brushless) |
| Matériau de la roue | Acier inoxydable |
| Pompe Casing Matériau | Fonte |
| Longueur du câble | 0.3 mètres |
| Tank Capacity (Cylindrical) | 24 litres |
| Dimensions du produit (L x l x H) | 30 x 19 x 22 cm |
| Poids de l'article | 1.5 kg |
| Couleur | Argent |
5. Configuration et installation
5.1 Placement
- Position the pump on a firm, level, and dry surface.
- Assurez une ventilation adéquate autour de la pompe pour éviter toute surchauffe.
- Protect the pump from direct exposure to weather elements (rain, direct sunlight, frost).
- Keep the pump as close as possible to the water source to minimize suction lift and maximize efficiency.
5.2 Raccordement des tuyaux
The pump is equipped with standard inch fittings for both suction and discharge pipes.
- Tuyau d'aspiration: Connect a rigid, airtight suction pipe (1 inch diameter) to the pump's inlet. Ensure all connections are sealed to prevent air leaks, which can affect priming and pump performance. A foot valve with a strainer should be installed at the end of the suction pipe submerged in the water source to prevent debris from entering the pump and to maintain prime.
- Tuyau de décharge : Connect a discharge pipe (1 inch diameter) to the pump's outlet. Use the provided three-way brass fitting, pressure switch, and pressure gauge as part of your water supply system. Ensure all connections are secure.
5.3 Amorçage de la pompe
This is a self-priming pump, but initial priming is crucial for proper operation. Before first use or after the pump has run dry:
- Assurez-vous que le tuyau d'aspiration soit entièrement immergé dans la source d'eau.
- Locate the priming plug on the top of the pump casing.
- Unscrew the priming plug and slowly fill the pump casing with clean water until it overflows.
- Replace and securely tighten the priming plug.
- Open any valves on the discharge side to allow air to escape during startup.
5.4 Connexion électrique
- Connect the pump's power cord to a grounded electrical outlet (220-240V, 50Hz).
- Ensure the electrical circuit is protected by a Residual Current Device (RCD) for added safety.
6. Fonctionnement
6.1 Démarrage de la pompe
- Ensure the pump has been properly primed (Section 5.3).
- Verify all pipe connections are secure and leak-free.
- Plug the pump into the power outlet. The pump will start automatically if connected to an automated system with a pressure switch.
- Observe the pressure gauge. The pressure should rise as the pump builds pressure.
- If the pump does not draw water within a few minutes, switch it off, re-prime, and check for air leaks in the suction line.
6.2 Fonctionnement automatique
When integrated into a water supply system with the included pressure switch, the pump will automatically start when water pressure drops (e.g., when a tap is opened) and stop when the desired pressure is reached (e.g., when the tap is closed). The 24-liter cylindrical tank helps maintain consistent pressure and reduces pump cycling.
6.3 Arrêt de la pompe
For temporary shutdown, close all water outlets. The pump will stop automatically if operating in an automated system. For complete shutdown or extended periods of non-use, unplug the pump from the power supply.
7. Entretien
Regular maintenance ensures optimal performance and extends the lifespan of your pump. Always disconnect the power supply before performing any maintenance.
7.1 Contrôles réguliers
- Inspectez le cordon d’alimentation et la fiche pour déceler tout signe de dommage.
- Check all pipe connections for leaks. Tighten if necessary.
- Ensure the foot valve strainer is clear of debris. Clean if clogged.
- Soyez attentif aux bruits inhabituels pendant le fonctionnement, car ils peuvent indiquer un problème.
7.2 Nettoyage
Essuyez l'extérieur de la pompe avec de la publicitéamp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure the motor's ventilation openings are free from dust and debris.
7.3 Hivernage (pour les climats froids)
If the pump is exposed to freezing temperatures, it must be drained to prevent damage:
- Débrancher l'alimentation électrique.
- Drain all water from the pump casing by unscrewing the drain plug (if present) or by tilting the pump.
- Disconnect the suction and discharge pipes and drain them completely.
- Rangez la pompe dans un endroit sec et à l'abri du gel.
8. Dépannage
Avant de contacter le service client, veuillez consulter le tableau suivant pour connaître les problèmes courants et leurs solutions.
| Problème | Cause possible | Solution |
|---|---|---|
| La pompe ne démarre pas | Pas d'alimentation électrique Cordon d'alimentation/prise défectueux Protection contre les surcharges du moteur déclenchée |
Vérifiez la connexion électrique et la prise Inspecter et remplacer si endommagé Allow motor to cool, then restart. Check for blockages. |
| La pompe fonctionne mais l'eau n'est pas distribuée. | Pompe non amorcée Fuite d'air dans la conduite d'aspiration Hauteur d'aspiration trop élevée Foot valve clogged or stuck Source d'eau vide |
Re-prime the pump (Section 5.3) Check all suction connections for leaks and tighten Relocate pump closer to water source Clean or replace foot valve Ensure adequate water in source |
| Débit ou pression faibles | Partial blockage in pipes/impeller Fuite d'air dans la conduite d'aspiration Roue usée Incorrect pressure switch setting |
Inspect and clear blockages Check and seal suction connections Contactez un personnel de service qualifié Adjust pressure switch according to manufacturer guidelines (if adjustable) |
| La pompe s'allume et s'éteint fréquemment. | Leak in discharge system Pressure tank pre-charge incorrect Pressostat défectueux |
Check for leaks in pipes, fittings, or fixtures Check and adjust pressure tank air pre-charge Inspect and replace pressure switch if necessary |
9. Garantie et assistance
This Total TWP47506 750W Automatic Jet Water Pump comes with a standard manufacturer's warranty. Please refer to the warranty card included with your purchase for specific terms and conditions, including warranty period and coverage details.
For technical assistance, spare parts, or warranty claims, please contact Total customer support through your retailer or visit the official Total website for contact information in your region. When contacting support, please have your model number (TWP47506) and purchase date available.