Raspberry Pi Compute Module 3+ Lite User Manual

1. Introduction

The Raspberry Pi Compute Module 3+ Lite is an industrial-grade System-on-Module (SoM) that integrates the core components of a Raspberry Pi 3 Model B+ into a compact SODIMM form factor. This module is designed for embedded applications, offering a powerful quad-core processor and 1GB of LPDDR2 SDRAM. It provides access to more GPIO pins when used with a compatible I/O board (not included), making it suitable for a wide range of industrial and consumer products.

2. Consignes de sécurité

Please read all safety instructions carefully before using the Raspberry Pi Compute Module 3+ Lite.

• The Compute Module must only be handled in compliance with Electrostatic Discharge (ESD) protection measures.
• Before connecting to a power supply, ensure that no thermal overload will occur. Adequate ventilation is crucial.
• Do not operate the module in humid, wet, or excessively dusty environments.
• Never allow direct contact with water or any other conductive liquids.
• Only connect the module with recommended power supplies that provide the correct voltage et actuel.
• Liquids, dust, and overvoltages can lead to dangerous situations or cause permanent defects.
• Avoid storing the module in an enclosed housing without proper ventilation to prevent damage or corrosion.
• Do not attempt to repair defective modules or components yourself. Unauthorized repairs can void your warranty and cause further damage.
• Recycle defective or discarded Compute Modules according to local electronic waste disposal regulations.

3. Produit terminéview

The Raspberry Pi Compute Module 3+ Lite offers a compact and robust solution for embedded systems. Its design allows for integration into custom hardware, leveraging the extensive Raspberry Pi ecosystem.

Caractéristiques principales :

• Processeur: Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC running at 1.2GHz.
• BÉLIER: 1GB of LPDDR2 SDRAM.
• Facteur de forme : Based on the SODIMM standard, enabling use with standard connectors.
• GPIO : Provides access to a greater number of GPIO pins compared to standard Raspberry Pi boards when used with an appropriate I/O board.

Disposition des modules :

Figure 3.1 : Devant view of the Raspberry Pi Compute Module 3+ Lite, showing the main processor and memory components.

Figure 3.2 : Dos view of the Raspberry Pi Compute Module 3+ Lite, illustrating the SODIMM connector and additional circuitry.

4. Installation

The Compute Module 3+ Lite requires a compatible I/O board for operation. This section outlines the general steps for initial setup.

1. Prepare I/O Board: Ensure your I/O board is compatible with the Compute Module 3+ Lite and has the necessary power supply and peripheral connections.
2. Insert Compute Module: Carefully align the Compute Module 3+ Lite with the SODIMM connector on your I/O board. Apply even pressure to insert it fully until it is securely seated.
3. Connectez les périphériques : Connect any required peripherals such as a display (HDMI), keyboard, mouse, and network cable to the I/O board.
4. Alimentation: Connect a suitable power supply to your I/O board. Refer to your I/O board's documentation for specific power requirements.
5. Système opérateur: The Compute Module 3+ Lite does not have onboard eMMC storage. You will need to provide an operating system via an SD card (if your I/O board supports it) or network boot. It is compatible with NOOBS 3.0.0 or later.

5. Mode d'emploi

Once the Compute Module 3+ Lite is set up with an I/O board and an operating system, its operation is similar to a standard Raspberry Pi.

• Mise sous tension : Apply power to the I/O board. The module should boot up, and you should see output on your connected display.
• OS Interaction: Interact with the operating system using your connected keyboard and mouse.
• Installation du logiciel : Install software and applications as needed for your specific project or application.
• Utilisation des GPIO : Utilize the GPIO pins for interfacing with external hardware, following the documentation for your I/O board and the Raspberry Pi GPIO libraries.
• Fermer: Always perform a proper shutdown of the operating system before disconnecting power to prevent data corruption.

6. Entretien

Proper maintenance ensures the longevity and reliable operation of your Compute Module 3+ Lite.

• Garder propre: Regularly clean the module and I/O board to prevent dust accumulation, which can lead to overheating or short circuits. Use a soft, dry brush or compressed air.
• Contrôle de l'environnement : Operate the module within its specified temperature and humidity ranges. Avoid extreme conditions.
• Mises à jour du micrologiciel : Keep the operating system and any relevant firmware updated to ensure optimal performance and security.
• Connexions sécurisées : Periodically check all connections (SODIMM, power, peripherals) to ensure they are secure and free from corrosion.
• Protection ESD : When handling the module, always observe ESD precautions to prevent damage from static electricity.

7. Dépannage

Cette section propose des solutions aux problèmes courants que vous pourriez rencontrer.

• Pas d'alimentation/Pas de démarrage :
  • Assurez-vous que l'alimentation est correctement connectée et fournit un volume suffisanttage and current for the I/O board and module.
  • Verify the Compute Module is correctly seated in the SODIMM slot.
  • Check for any visible damage to the module or I/O board.
• Aucune sortie d'affichage :
  • Confirm the display cable (e.g., HDMI) is securely connected to both the I/O board and the monitor.
  • Vérifiez que le moniteur est allumé et réglé sur la source d'entrée appropriée.
  • Verify that the operating system image is correctly installed and configured for display output.
• Peripheral Issues (Keyboard/Mouse/USB):
  • Try connecting peripherals to different USB ports on the I/O board.
  • Test peripherals with another device to confirm they are functional.
  • Ensure the operating system has the necessary drivers.
• Surchauffe:
  • Ensure adequate ventilation around the module and I/O board.
  • Consider adding a heatsink or fan if operating in high-temperature environments or under heavy load.
  • Reduce CPU load if possible.

8. Spécifications

9. Garantie et assistance

For warranty information and technical support, please contact Raspberry Pi directly.

Informations sur le fabricant :

Raspberry Pi Ltd.
194 Cambridge Science Park, Milton Road
GB - CB4 0AB Cambridge
E-mail: compliance@raspberrypi.com
Website: https://www.raspberrypi.com

Numéro DEEE : 20453810

Personne responsable pour l'UE :

Raspberry Pi Ireland Limited
3 Dublin Landings
IE - D01 C4E0 North Wall Quay, Dublin 1
E-mail: compliance@raspberrypi.com
Website: https://www.raspberrypi.com