SOMMER Pearl 4018 Garage Door Remote Control User Manual

1. Introduction

This manual provides instructions for the safe and efficient operation, setup, and maintenance of your SOMMER Pearl 4018 4018V000 TX55-868-4 garage door remote control. This device utilizes the SOMloq2 radio system and is compatible with Somloq Rollingcode systems, as well as Pro Teckentrup Drive models 4020, 4026, and 4031 Slider.

Figure 1 : SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control. This image shows the compact, modern design of the remote control, featuring four buttons and a stainless steel application.

2. Consignes de sécurité

• Keep the remote control out of reach of children to prevent accidental operation of the garage door.
• Ne laissez pas les enfants jouer avec la télécommande ou l'ouvre-porte de garage.
• Avant de manœuvrer la porte de garage, assurez-vous qu'elle soit visible et dégagée de tout obstacle.
• Do not operate the garage door if people or objects are in its path.
• Jetez les piles conformément à la réglementation locale. Ne les incinérez pas.
• Avoid exposing the remote control to extreme temperatures, moisture, or direct sunlight.

3. Contenu du colis

Vérifiez que tous les éléments sont présents dans votre colis :

• SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control (quantity as purchased, typically 2 units)
• 3V CR2032 Lithium-metal battery (pre-installed or included)

4. Installation et programmation

The SOMMER Pearl 4018 remote control must be programmed to your garage door opener receiver. The exact programming steps may vary slightly depending on your specific SOMMER garage door opener model. Refer to your garage door opener's manual for precise instructions. A common programming method is outlined below:

1. Localisez le récepteur : Identify the garage door opener's motor unit. On the motor unit, locate the "Learn" or "Program" button. This button is often small and may be recessed.
2. Activer le mode d'apprentissage : Press and immediately release the "Learn" or "Program" button on your garage door opener. The indicator light on the opener will typically illuminate or flash, indicating it is in learn mode. You usually have about 30 seconds to complete the next step.
3. Programmer la télécommande : Within the learn mode timeframe, press and hold the desired button on your SOMMER Pearl 4018 remote control that you wish to use for operating the garage door.
4. Confirmer la programmation : Release the button on the remote control once the garage door opener's indicator light flashes or changes color, or if the garage door moves slightly. This indicates successful programming.
5. Opération de test : Press the programmed button on your remote control to ensure it operates the garage door correctly.
6. Programmer des télécommandes supplémentaires : Repeat these steps for any additional SOMMER Pearl 4018 remote controls you wish to program.

Note: If your garage door opener has a different programming procedure (e.g., using a master remote or a specific sequence), please consult your opener's manual.

5. Mode d'emploi

Once programmed, operating your SOMMER Pearl 4018 remote control is straightforward:

• Ouverture/fermeture de la porte : Press the programmed button on your remote control once. The garage door will begin to open or close.
• Bloquer la porte : Appuyez à nouveau sur le même bouton programmé pendant que la porte est en mouvement pour l'arrêter.
• Plusieurs portes : If you have programmed multiple garage doors to different buttons on your remote, press the corresponding button for the desired door.
• Gamme: The remote control has an approximate range of 50-140 meters, depending on environmental conditions and obstructions.

6. Entretien

6.1. Remplacement de la batterie

The SOMMER Pearl 4018 remote control uses a 3V CR2032 Lithium-metal battery. When the remote's range decreases significantly or it stops responding, it is likely time to replace the battery.

1. Ouvrez le Casing: Ouvrez soigneusement le boîtier de la télécommandeasing. This usually involves prying it open with a small flat-head screwdriver or a similar tool at a designated notch.
2. Retirer l'ancienne batterie : Note the orientation of the old CR2032 battery (positive (+) side up or down). Gently remove the old battery.
3. Insérer une nouvelle batterie : Insert a new 3V CR2032 Lithium-metal battery, ensuring the correct polarity. The positive (+) side typically faces upwards.
4. Fermer Casing: Clipsez la télécommande casing pour les remettre en place en toute sécurité.
5. Test: Testez la télécommande pour vous assurer qu'elle fonctionne correctement avec la nouvelle pile.

6.2. Nettoyage

Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or allow moisture to enter the casing.

7. Dépannage

8. Spécifications

• Modèle: Pearl 4018 4018V000 TX55-868-4
• Système radio : SOMloq2
• Boutons: 4
• Fréquence radio: FM 868.8 MHz, FM 868.95 MHz
• Gamme: Approx. 50-140 meters (environment dependent)
• Dimensions: 79 x 26 x 13 mm (3.11 x 1.02 x 0.51 pouces)
• Type de batterie : 3V CR2032 Lithium-metal
• Poids: 40 g (1.41 oz)
• Compatibilité: Somloq Rollingcode system, Pro Teckentrup Drive (compatible with 4020, 4026, 4031 Slider)

9. Garantie et assistance

For warranty information and technical support, please refer to the documentation provided with your original purchase or contact SOMMER customer service directly. Contact details can typically be found on the manufacturer's official website.