Introduction
This manual provides essential instructions for the safe and efficient use of the Perel AC028 Intelligent Charger. This device is specifically designed for charging 12V lead-acid batteries, including Gel, AGM, and EFB types, utilizing a sophisticated 3-stage automatic charging cycle to optimize battery life and performance.
Consignes de sécurité
Always read and understand all safety warnings and instructions before operating the charger. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- This charger is intended for 12V lead-acid batteries (Gel, AGM, EFB) only. Do not use with other battery types.
- Battery charging can produce explosive gases. Ensure adequate ventilation during charging and keep away from flames, sparks, and smoking materials.
- Débranchez toujours le chargeur de l'alimentation secteur avant de connecter ou de déconnecter la batterie.
- Avoid charging a frozen battery. Allow it to thaw before attempting to charge.
- Gardez le chargeur et la batterie hors de portée des enfants et des animaux domestiques.
- Do not expose the charger to rain or excessive moisture. The unit has an IP65 rating, meaning it is protected against dust and low-pressure water jets, but it is not submersible.
- Si le cordon d'alimentation est endommagé, il doit être remplacé par le fabricant, son agent de service ou des personnes de qualification similaire pour éviter tout danger.
Caractéristiques du produit
- 3-Stage Automatic Charging Cycle: Ensures optimal charging and extends battery life.
- Compatibilité de la batterie : Designed for 12V lead-acid batteries, including Gel, AGM, and EFB types.
- Puissance nominale: 12 Vcc, 1.5 A.
- Classe de protection IP65 : Offre une protection contre la pénétration de poussière et les jets d'eau à basse pression provenant de toutes les directions.
- Conception compacte : Facile à stocker et à transporter.
Caractéristiques
| Modèle | AC028 |
| Vol d'entréetage | 220-240 VAC |
| Fréquence | 50/60 Hz |
| Volume de sortietage | 12 VCC |
| Courant de sortie | 1.5 A |
| Courant nominal | 0.25 A |
| Dimensions (L x l x H) | 147 x 72 x 42 mm |
| Poids | 376 g |
| Classe de protection IP | IP65 |
| Types de batteries compatibles | 12V Lead-Acid (Gel, AGM, EFB) |
| Longueur du câble principal | 1.5 m |
| Longueur du câble de chargement | 1 m |
Installation
- Ensure the Perel AC028 charger is disconnected from the mains power outlet.
- Connectez le rouge (+) clamp of the charger to the positive (+) terminal of the 12V lead-acid battery.
- Connectez le noir (-) clamp of the charger to the negative (-) terminal of the 12V lead-acid battery.
- Verify that both connections are secure and properly seated to prevent arcing or poor contact.
- Plug the charger's main power cable into a suitable 220-240 VAC, 50/60 Hz mains power outlet.
Mode d'emploi
Once connected to the battery and mains power, the charger will automatically initiate its 3-stage processus de charge.
- Indicateur d'alimentation : The 'POWER' LED will illuminate when the charger is connected to the mains power supply.
- Indicateur de charge : The 'CHARGING' LED will illuminate when the battery is actively being charged.
- Indicateur complet : The 'FULL' LED will illuminate when the battery has reached a full charge. At this point, the charger will switch to a maintenance mode to prevent overcharging.
The charger can remain connected to the battery for extended periods for maintenance charging, ensuring the battery remains at an optimal charge level.
Entretien
- Regularly inspect the charger's cables, clamps et casing for any signs of damage, wear, or corrosion. Do not use the charger if any part is damaged.
- Veillez à ce que le chargeur reste propre et exempt de poussière et de débris. Utilisez un chiffon sec pour le nettoyer. N'utilisez pas de solvants ni de nettoyants abrasifs.
- Store the charger in a cool, dry, and well-ventilated area when not in use.
- Ensure the battery terminals are clean before connecting the charger for optimal contact.
Dépannage
The Perel AC028 charger is equipped with error indicators to help diagnose common issues:
| Code d'erreur | Description | Action |
|---|---|---|
| F01 | Short circuit / Reverse connection / No connection | Check battery connections for correct polarity (+ to +, - to -). Ensure clamps are securely attached and there is no short circuit. |
| F02 | Connexion lâche | Vérifiez que la batterie clamps are tightly connected to the battery terminals. |
| F03 | Vol batterietage trop haut | This charger is for 12V batteries. Ensure you are not attempting to charge a battery with a higher nominal voltage. |
| F04 | Batterie défectueuse | The battery may be severely discharged, damaged, or at the end of its life. It might not be able to accept a charge. Consult a battery specialist. |
Garantie et assistance
For detailed warranty information, terms, and conditions, please refer to the documentation provided with your purchase or visit the official Perel website. For technical support or service inquiries, contact your retailer or the manufacturer's customer service department.