Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Puig Handguard Extension, model 9214F. This accessory is designed to enhance the wind protection offered by your motorcycle's existing handguards, improving rider comfort during various riding conditions. Please read these instructions carefully before proceeding with installation or use.
Compatibilité:
- Yamaha MT-07 TRACER (2016-2017)
- Yamaha TRACER 700 (2018-2019)
- Yamaha TRACER 700 GT (2019)
Configuration et installation
Before beginning installation, ensure you have all components included with your Puig Handguard Extension. Refer to the included instruction sheet for a detailed list of parts and specific installation steps. Basic tools typically required for motorcycle accessory installation may be needed.
- Préparation: Garez votre moto sur une surface stable et plane. Assurez-vous que le moteur est éteint et froid.
- Identifier les points de fixation : The handguard extensions are designed to attach to your motorcycle's existing handguards. Locate the designated mounting points on your current handguards.
- Pièce jointe: Carefully align the Puig Handguard Extension with the mounting points. Secure it using the provided hardware. Ensure all fasteners are tightened securely, but do not overtighten to avoid damaging the acrylic material or existing components.
- Répétez l'opération de l'autre côté : Follow the same procedure for the handguard extension on the opposite side of the motorcycle.
- Vérification finale : After installation, gently test the stability of the extensions. Ensure they do not interfere with the operation of the handlebars, levers, or any other controls.
Image: Puig Handguard Extension (Model 9214F) shown installed on a Yamaha MT-07 Tracer motorcycle, demonstrating its position relative to the handlebars and windscreen. The dark smoke finish is visible.
Fonctionnement et utilisation
The Puig Handguard Extension is designed to provide additional protection from wind and light debris for the rider's hands. Once properly installed, no specific operational steps are required. The extensions function passively by increasing the surface area of the existing handguards.
- Enhanced Wind Protection: The primary benefit is reduced wind blast on the hands, which can contribute to greater comfort, especially in colder weather or at higher speeds.
- Light Debris Deflection: Provides a barrier against small stones, insects, and other light road debris.
Always ensure the extensions are securely fastened before each ride. If you notice any looseness, re-tighten the fasteners immediately.
Entretien
To ensure the longevity and clear appearance of your Puig Handguard Extensions, follow these simple maintenance guidelines:
- Nettoyage: Clean the acrylic surface with a soft cloth and mild soap and water. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the acrylic. Rinse thoroughly with clean water and dry with a soft, lint-free cloth.
- Inspection: Periodically inspect the extensions and their mounting hardware for any signs of wear, damage, or looseness. Tighten any loose fasteners.
- Stockage: If storing the motorcycle for an extended period, ensure the handguard extensions are clean and dry.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Handguard extensions feel loose or vibrate. | Les fixations ne sont pas suffisamment serrées. | Carefully re-tighten all mounting bolts and screws. Do not overtighten. If the issue persists, check for proper alignment and ensure no components are missing or damaged. |
| Reduced wind protection is observed. | Incorrect installation or expectations. | Ensure the extensions are correctly positioned as per the instruction sheet. Note that these are extensions and provide supplementary protection, not a complete wind barrier. |
| Scratches or damage to the acrylic. | Improper cleaning methods or impact. | Use only soft cloths and mild soap for cleaning. Avoid abrasive materials. Minor scratches may be polished out with specialized acrylic polish; severe damage may require replacement. |
Caractéristiques
| Fonctionnalité | Détail |
|---|---|
| Marque | Puig |
| Numéro de modèle | 9214F |
| Matériel | Acrylique |
| Finition extérieure | Transparent (Dark Smoke) |
| Couleur | Fumée noire |
| Type de service de véhicule | Vehicle Specific (Yamaha MT-07 Tracer, Tracer 700) |
| Position de la pièce | Frontale |
| Nombre de pièces | 2 (for a pair) |
| Type d'installation | Vehicle-specific fitment |
| Numéro de pièce du fabricant | 9214F |
| OEM Equivalent Part Number | M9214F |
| Code international des articles (EAN) | 08436563733635 |
Garantie et assistance
For any questions regarding installation, operation, or potential defects, please refer to the official Puig webConsultez leur site web ou contactez directement leur service client. Conservez votre reçu d'achat comme preuve d'achat pour toute réclamation au titre de la garantie.
Fabricant: Puig
Website: puig.tv
Note: Specific warranty terms and conditions may vary by region. Please consult the documentation provided with your product or the manufacturer's official channels for detailed warranty information.
