Brondell Swash SE600 Elongated Bidet Toilet Seat User Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Brondell Swash SE600 Elongated Bidet Toilet Seat. This electronic bidet seat is designed to enhance personal hygiene with features such as a heated seat, warm air dryer, oscillating stainless-steel nozzle for both rear and front wash, gentle massage pulse, deodorizer, power-saving eco-mode, and an ambient nightlight.

Consignes de sécurité

Please read all instructions carefully before installation and use. Keep this manual for future reference. Ensure the bidet seat is connected to a properly grounded GFCI outlet. Do not immerse the unit in water. Disconnect power before cleaning or servicing. Avoid using abrasive cleaners on the bidet seat. This product is intended for household use only.

Contenu du colis

Vérifiez que tous les composants sont présents avant de commencer l'installation :

• Brondell Swash SE600 Bidet Toilet Seat (Elongated)
• Wireless Remote Control (with 2 AAA batteries)
• Mounting Plate and Bolts
• T-Valve (for water connection)
• Tuyau de bidet
• Washers and Nuts
• Manuel de l'utilisateur (ce document)

Configuration et installation

Follow these steps for proper installation of your Brondell Swash SE600 bidet toilet seat. No special tools are typically required, and installation can be completed in under an hour.

1. Measure Your Toilet for Proper Fit

Before installation, ensure your toilet is compatible with an elongated bidet seat. Measure the distance from the bolt holes to the front of the toilet bowl (Dimension A) and the distance from the center of the bolt holes to the toilet tank (Dimension B). Also, measure the distance between the bolt holes (Dimension C).

Image: Diagram illustrating how to measure your toilet for proper bidet seat fit. It shows three key measurements: A (from bolt holes to front of bowl), B (from bolt holes to tank), and C (distance between bolt holes). For elongated seats, Dimension A should be 18"-19.5".

Image: Visual comparison of round (16.5") and elongated (18.5") toilet seat dimensions, highlighting the difference in length.

2. Prepare Your Toilet

1. Remove your existing toilet seat and thoroughly clean the toilet bowl and surrounding area.
2. Turn off the water supply at the shut-off valve located at the wall behind your toilet.
3. Flush the toilet to drain the tank completely. Hold down the flush handle until all water is drained.
4. Unscrew the flexible water supply line from the fill valve at the bottom of the toilet tank. Have a small bucket or towel ready to catch any residual water.

3. Installez la vanne en T

1. Connect the provided T-valve to the fill valve under the toilet tank. Ensure the rubber gasket is properly seated to prevent leaks.
2. Reconnect the flexible water supply line to the bottom of the T-valve.

4. Installez la plaque de montage

1. Place the mounting plate over the bolt holes on the toilet, ensuring the arrow on the plate points towards the toilet bowl.
2. Slide the mounting bolts through the holes in the toilet and secure them with the provided washers and nuts from underneath. Leave the bolts loose enough to allow for minor adjustments later.

5. Fixez le siège du bidet

1. Place the Swash bidet seat flat onto the toilet, in front of the mounting plate.
2. Slide the Swash seat towards the tank onto the mounting plate until it clicks securely into place.
3. Adjust the position of the seat by sliding it forward or backward for the best fit, then tighten the nuts under the toilet to secure it.

6. Connect Water and Power

1. Connect the elbow side of the bidet hose to the Swash's water inlet on the side of the seat.
2. Connect the open end of the bidet hose to the T-valve.
3. Turn on the water supply at the shut-off valve and check for any leaks.
4. If no leaks are present, plug the Swash into the nearest Ground Fault Circuit Interrupter (GFCI) outlet. The bidet should power on, illuminating the power indicator light. If not, press any button on the seat's control panel.

Guide vidéo d'installation

Mode d'emploi

The Brondell Swash SE600 features a wireless remote control for easy operation. Ensure the remote has batteries installed and is functioning correctly.

Contrôle à distance surview

Image: The wireless remote control for the Brondell Swash SE600, displaying various buttons for wash functions (Rear, Front, Dry), settings adjustments (Nozzle Position, Water Pressure/Dry Temp, Water Temp, Seat Temp), and advanced features (Massage, Move, Auto Mode, Deodorize).

Basic Wash Functions

1. Lavage arrière : Press the "Rear" button for a posterior wash.
2. Lavage avant : Appuyez sur le bouton « Avant » pour un lavage féminin.
3. Stop: Press the "Stop" button to end any active wash or dry cycle.

Réglage des paramètres

• Température de l'eau : Use the "Water Temp" button to cycle through available water temperature settings (e.g., low, medium, high, off). Allow 3-4 minutes for the water to heat to your desired temperature.
• Pression de l'eau : Use the "+" and "-" buttons under "Water Pressure / Dry Temp" to adjust the water spray intensity.
• Position de la buse : Use the "Nozzle Position" up and down arrows to adjust the nozzle's projection for optimal cleaning.
• Température du siège : Use the "Seat Temp" button to adjust the heated seat temperature.

Image : Un gros plan view of the bidet's self-cleaning stainless steel nozzle, illustrating its five adjustable positions and aerated water spray for effective cleaning.

Fonctionnalités avancées

• Sécheur à air chaud : After a wash cycle, press the "Dry" button to activate the warm air dryer. Adjust the dry air temperature using the "+" and "-" buttons under "Water Pressure / Dry Temp".
• Massage: Press the "Massage" button for a pulsating wash spray.
• Se déplacer: Press the "Move" button to activate an oscillating nozzle movement for a wider cleaning area.
• Mode automatique: Press "Auto Mode" for a complete wash and dry cycle.
• Désodorisant: The built-in deodorizer automatically activates to neutralize odors.
• Veilleuse : The ambient nightlight provides soft illumination for nighttime use.
• Mode écologique: Activate "Eco Mode" to conserve energy by lowering the seat and water heating temperatures when not in use.

Entretien

Regular cleaning and maintenance will ensure the longevity and optimal performance of your Brondell Swash SE600.

• Nettoyage extérieur : Essuyez les surfaces extérieures avec un chiffon doux, damp Utilisez un chiffon et un nettoyant doux non abrasif. Évitez les produits chimiques agressifs et les tampons abrasifs.
• Nettoyage des buses : The stainless-steel nozzle is self-cleaning. For additional cleaning, you can manually extend the nozzle (refer to the full owner's manual for specific instructions) and gently clean it with a soft brush.
• Entretien du filtre: Periodically check the water inlet filter for sediment buildup. Clean if necessary to maintain water flow.
• Stockage à long terme : If storing the bidet seat for an extended period, drain all water from the unit and disconnect it from power.

Dépannage

For further troubleshooting or issues not listed, please refer to the comprehensive owner's manual or contact Brondell customer support.

Caractéristiques

• Modèle: SE600
• Taper: Siège de toilette bidet allongé
• Couleur: Blanc
• Matériel: Plastique
• Dimensions du produit : 20.7 po L x 14.9 po l
• Poids de l'article : 9.7 livres
• Voltage: 120 volts
• Quoitage: 660.00 watts
• Piles : 2 piles AAA (fournies pour la télécommande)
• Caractéristiques: Heated Seat, Warm Air Dryer, Oscillating Stainless-Steel Nozzle, Rear/Front Wash, Massage, Move, Auto Mode, Deodorizer, Ambient Nightlight, Eco Mode.

Garantie et assistance

For warranty information, product registration, or technical support, please visit the official Brondell webConsultez leur site web ou contactez leur service client. Conservez votre reçu d'achat comme preuve d'achat pour toute réclamation au titre de la garantie.

Brondell Customer Support: www.brondell.com/support