Introduction
This manual provides instructions for the proper installation, operation, and maintenance of the Hager 2500 Series Cylindrical Passage Lock, model 129002. This lock is designed for standard duty commercial applications and is suitable for doors requiring a non-locking function, allowing free passage from either side at all times.
Consignes de sécurité
Always wear appropriate safety gear, such as gloves and eye protection, during installation. Ensure all tools are in good working condition. If you are unsure about any step, consult a qualified professional.
Contenu du colis
Vérifiez que tous les composants sont présents avant de commencer l'installation :
- Hager 2500 Series Cylindrical Passage Lock assembly (Withnell Lever Style)
- Mécanisme de verrouillage
- Strike plate (ASA Strike)
- Vis de montage
- Operating keys (two supplied, for specific internal components, not for locking function)
- Installation template (if included with physical product)
Configuration et installation
Follow these steps for proper installation of the Hager 2500 Series Cylindrical Passage Lock.
1. Préparation de la porte
Ensure your door is prepared with the following standard dimensions:
- Alésage transversal : 2-1/8 inches (54 mm) diameter
- Edge Bore (Latch Hole): 1 inch (25 mm) diameter
- Décalage: 2-3/4 pouces (70 mm)
Use the provided template (if applicable) to mark and drill holes accurately. Incorrect drilling can affect lock function and security.
2. Install Latch Mechanism
- Insert the latch mechanism into the edge bore of the door, ensuring the bevel of the latch bolt faces the door frame.
- Fixez le loquet avec les vis fournies.
3. Install Lock Chassis
- Align the lock chassis with the cross bore, ensuring the spindle engages with the latch mechanism.
- Insert the exterior and interior lever assemblies.
- Secure the lock chassis with the through-bolts or mounting screws. The design features no exposed mounting screws for a clean appearance.
4. Install Strike Plate
- Mark the position for the ASA strike plate on the door frame, aligning it with the latch bolt.
- Chisel out the mortise for the strike plate to sit flush with the door frame.
- Fixez la gâche à l'aide des vis fournies.
Image 1: Hager 2500 Series Cylindrical Passage Lock, Withnell Lever Style, in Satin Chrome finish. This image shows the complete lever set, including both interior and exterior levers and the cylindrical chassis.
Mode d'emploi
The Hager 2500 Series Cylindrical Passage Lock is designed for non-locking applications. It allows free entry and exit at all times.
- To open the door, simply depress the lever handle on either side.
- Release the lever to allow the latch bolt to extend and secure the door in the closed position.
Note: While two operating keys are supplied, these are typically for internal component access or specific installation adjustments, not for a locking function on a passage set. This lock does not provide security locking.
Entretien
Un entretien régulier garantit la longévité et le bon fonctionnement de votre serrure.
- Nettoyage: Nettoyez les surfaces extérieures avec un chiffon doux et sec.amp Chiffon. Évitez les nettoyants abrasifs ou les solvants, qui peuvent endommager la finition.
- Lubrification: Periodically apply a small amount of graphite-based lubricant to the latch bolt mechanism if it becomes stiff. Do not use oil-based lubricants, as they can attract dust and debris.
- Inspection: Annually inspect all screws and components for tightness. Tighten any loose screws to prevent excessive wear.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Le levier est rigide ou difficile à tourner. | Accumulation de saletés ou manque de lubrification. | Clean the mechanism and apply graphite lubricant. |
| Le pêne dormant ne se rétracte pas complètement. | Misalignment of lock components or strike plate. | Check alignment of lock chassis and strike plate. Ensure screws are tight. |
| Door rattles when closed. | Strike plate not properly aligned or mortised. | Adjust the strike plate position or depth to ensure a snug fit with the latch bolt. |
Caractéristiques
| Fonctionnalité | Détail |
|---|---|
| Numéro de modèle | 129002 |
| Série | Série 2500 |
| Type de serrure | Cylindrical Passage Lock (Non-locking) |
| Matériel | Heavy Gauge Steel, Zinc (Handle Material: Zinc) |
| Finition | Chrome satiné |
| Style de levier | Withnell |
| Backset | 2-3/4 pouces (70 mm) |
| Door Prep - Cross Bore | 2-1/8 inches (54 mm) diameter |
| Door Prep - Latch Hole (Edge Bore) | 1 inch (25 mm) diameter |
| Orientation de la main | Non remis |
| Grade | Grade 2 (Standard Duty Commercial) |
| Plaque de frappe | Grève de l'ASA |
| Composants inclus | 2510 WTN US26D (Lock assembly, latch, strike, screws, 2 operating keys) |
Informations sur la garantie
Hager products are manufactured to high standards. For specific warranty terms and conditions applicable to the 2500 Series Cylindrical Passage Lock, please refer to the official Hager website or contact Hager customer support directly. Keep your purchase receipt as proof of purchase.
Assistance clientèle
If you require further assistance or have questions regarding your Hager 2500 Series Cylindrical Passage Lock, please contact Hager customer support:
- Website: Visit the official Hager webSite regroupant les ressources d'assistance et les informations de contact.
- Contact: Refer to the packaging or Hager's website pour les numéros de téléphone ou les adresses e-mail.
When contacting support, please have your model number (129002) and purchase details available.
