Woods 59408WD Outdoor Hard-Wired Post Eye Light Control Instruction Manual

1. Introduction

The Woods 59408WD Outdoor Hard-Wired Post Eye Light Control is designed to automatically turn your outdoor lighting on at dusk and off at dawn. This photocell light sensor provides reliable, energy-efficient control for various outdoor light fixtures, ensuring your property is illuminated when needed without manual intervention. It is suitable for hard-wired installations in appropriate enclosures.

2. Consignes de sécurité

• AVERTISSEMENT: Risque de choc électrique. Coupez l'alimentation au niveau du disjoncteur ou du tableau électrique avant toute installation ou intervention.
• This device is intended for installation in accordance with the National Electrical Code and local regulations. If you are unsure about wiring, consult a qualified electrician.
• Ensure the device is installed in a dry location or within a weather-resistant enclosure to prevent water damage and ensure safe operation.
• Do not exceed the specified electrical ratings.

3. Contenu du colis

• Woods 59408WD Photocell Light Control
• Hardwire Black (integrated wiring)

4. Spécifications

5. Installation

5.1 Outils requis

• Tournevis
• Pinces à dénuder
• Wire nuts (appropriate size)
• Ruban électrique
• Voltage testeur
• Weather-resistant electrical enclosure (if installing outdoors in an exposed location)

5.2 Instructions de câblage

IMPORTANT: Assurez-vous que le courant est coupé au niveau du disjoncteur avant de commencer l'installation.

1. Préparez les fils : Strip approximately 1/2 inch of insulation from the ends of all wires (photocell, incoming power, and light fixture wires).
2. Connecter les fils neutres : Connectez le fil blanc from the photocell to the incoming fil blanc (neutre) from your power source and the fil blanc (neutre) of your light fixture. Secure with a wire nut.
3. Connect Line (Hot) Wire: Connectez le fil noir from the photocell to the incoming black (hot/line) wire from your power source. Secure with a wire nut.
4. Raccordez le fil de charge : Connectez le fil rouge from the photocell to the black (hot/load) wire of your light fixture. Secure with a wire nut.
5. Connexions sécurisées : Ensure all wire nuts are tight and connections are secure. Wrap each wire nut with electrical tape for added insulation and protection.
6. Mount Photocell: Mount the photocell in a location where it will receive natural daylight and is not obstructed by shadows or artificial light sources (e.g., other lights, car headlights) that could interfere with its operation. If installing outdoors, ensure it is within a suitable weather-resistant enclosure.
7. Restaurer l'alimentation : Once all connections are secure and the photocell is mounted, restore power at the circuit breaker.

Note: The photocell may have a built-in delay (typically a few seconds to a few minutes) before activating or deactivating to prevent false triggers from transient light changes.

Image: The Woods 59408WD Post Eye Light Control, a compact black unit with a visible light sensor on the front.

Image : Un gros plan view of the photocell sensor on the Woods 59408WD unit, showing the light-sensitive element.

6. Fonctionnement

The Woods 59408WD Post Eye Light Control operates automatically based on ambient light levels:

• At Dusk: When natural light levels fall below a certain threshold, the photocell will detect darkness and activate the connected light fixture.
• At Dawn: When natural light levels rise above a certain threshold, the photocell will detect sufficient light and deactivate the connected light fixture.

There is an intentional delay in the switching mechanism (typically a few seconds to a few minutes) to prevent the light from cycling on and off due to temporary shadows, car headlights, or lightning flashes.

7. Entretien

The Woods 59408WD Post Eye Light Control requires minimal maintenance:

• Periodically inspect the photocell sensor for any dirt, dust, or debris that might obstruct its view of ambient light. Gently clean the sensor with a soft, damp chiffon si nécessaire.
• Ensure the area around the sensor remains clear of obstructions (e.g., growing foliage, new decorations) that could block natural light.
• Check wiring connections annually for any signs of wear or corrosion, especially in outdoor installations.

8. Dépannage

9. Garantie et assistance

For warranty information or technical support, please refer to the product packaging or contact Woods customer service directly. Keep your purchase receipt as proof of purchase.